embedded power for business-critical continuity sil40c2 series 4.5-13.8 vin single c-class non-isolated special features ? 40 a current rating ? input voltage range: 4.5-13.8 v ? output voltage: 0.6-5 v ? industry leading value ? cost optimized design ? excellent transient response ? output enable ? output voltage adjustability ? pathway for future upgrades ? supports silicon voltage migration ? resulting in reduced design-in and qual time ? rohs compliant 40 a current rating input voltage: 4.5-13.8 v no. of outputs: single output sxx06e rev. 08.01.06 page 1 of 2 electrical specifications output voltage see note 5 0.6-5 v output setpoint accuracy 0.1% trim resistors 1.0% line regulation low line to high line 0.2% load regulation full load to min. load 0.5% min./max. load 0 a/40 a overshoot at turn-on 0.5% max. undershoot at turn-off 100 mv max. ripple and noise 5 hz to 20 mhz see note 1 25 mv vin=5 v, vout=2.5 v transient response see notes 1, 2 130 mv max. deviation 50 s recovery to within regulation band input voltage range 4.5-13.8 vdc input current minimum load remote off 50 ma 5 ma input current (max.) see note 3 25 a @ lo max. start-up time remote on/off 3 ms input rev. 07.02.08 sil40c2 1 of 5 safety ul, cul can/csa 22.2 no. e139421 ul6950 file no. tbd t v product service (en60950) certificate no. tbd cb report and certificate to iec60950
rev. 07.02.08 sil40c2 2 of 5 embedded power for business-critical continuity thermal performance see note 5 operating ambient, temperature non-operating 0 c to +70 c -40 c to +125 c short-circuit hiccup, non-latching overvoltage protection hiccup, non-latching input capacitance see note 6 0 f output capacitance see note 7 0 f protection environmental specifications output power (max.) input voltage ovp output voltage output current (min.) output current (max.) effciency (typical) regulation line load model number (3,5) 200 w 4.5-13.8 vdc n/a 0.6-5 vdc 0 a 40 a 94% 0.2% 0.5% SIL40C2-00SADJ-VJ 200 w 4.5-13.8 vdc n/a 0.6-5 vdc 0 a 40 a 94% 0.2% 0.5% sil40c2-00sadj-hj 200 w 4.5-13.8 vdc n/a 0.6-5 vdc 0 a 40 a 94% 0.2% 0.5% smt40c2-00sadjj ordering information recommended system capacitance efficiency vin=5 v, vo=2.5 v, lo=20 a 94% switching frequency fixed 500 khz approvals and standards (pending) en60950 ul/cul6950 material flammability ul94v-0 weight 17 g (0.06 oz.) mtbf 12 v @ 40 c, 100% load bellcore 332 6,749,409 hours coplanarity 150 m general
rev. 07.02.08 sil40c2 3 of 5 embedded power for business-critical continuity notes: 1 measured as per recommended system capacitance. 2 di/dt = 10 a/s, vin = nom, tc = 25 c, load change = 0.75 lo to full lo and full lo to 0.75. 3 external input fusing is recommended. 4 additional part numbers may be available with different output voltages. 5 airflow dependent, 100 lfm minimum required. 6 no capacitors needed for ripple current capability. 7 no capacitors needed for stability. 8 tse rohs 5/6 (non-pb-free) compliant versions are also available on special request, please contact our local sales representative for details. 9 notice: some models may not support all options. please contact your local representative or use the on-line model number search tool at http://www. powerconversion.com to find a suitable alternative. 10 to order a horizontal mounting option with a pin length of 0.165", please use the model # sil40c2-00sa-hp5j product family product family sil = single in line smt = surface mount rated output current rated output current 06 = 6 a 15 = 15 a 20 = 20 a 30 = 30 a 40 = 40 a output voltage output voltage single adjustable output performance performance c = cost optimized generation generation blank = standard part 2 = increased current density input voltage input voltage 00 = 4.5-13.8 v output voltage adjustment of the sil40c2 series part number system with options the ultra-wide output voltage trim range offers major advantages to users who select the sil40c2 series. it is no longer necessary to purchase a variety of modules in order to cover different output voltages. the output voltage can be trimmed in a range of 0.6-5 v. when the sil40c2 converter leaves the factory, the output has been adjusted to the default volt - age of 0.6 v. mounting option mounting option v = vertical h = horizontal sil 40 c 2 - 00 sadj - v j rohs compliance (8) rohs compliance j = pb-free rohs 6/6 compliant 7,8 10,11 6 9 5 1,2,3 4 sil40c2 enable v in gnd r trim (for trim down) c out r l o a d power good v out +r sense c in figu r e 1: standa r d application drawing standard application drawing
rev. 07.02.08 sil40c2 4 of 5 embedded power for business-critical continuity mechanical drawings dimensions in inches (mm). tolerances (unless otherwise specifed) 2 places 0.030 (0.76) 3 places 0.010 (0.25) vertical mount horizontal mount dime nsions in inches (mm) tole rances (unless othe rw ise specified) 2 places 0.030 (0.76) 3 places 0.010 (0.25) 0.100 (2.54) 1.050 (26.67) 9 places 1.100 (27.94) 1.200 (30.48) 0.050 (1.27) ref 0.140 (3.56) typ pin 1 0.050 (1.27) typ 0.255 (6.48) 0.110 (2.79) 0.427 (10.85) 0.025 (0.64) .001 sq pins typ 0.062 (1.57) ref 0.100 (2.54) typ dime nsions in inches (mm) tole rances (unless othe rw ise specified) 2 places 0.030 (0.76) 3 places 0.010 (0.25) 1.100 (27.94) 1.200 (30.48) pin 1 0.255 (6.48) 0.110 (2.79) ref 0.468 (11.89) 0.062 (1.57) ref .150 (3.81) typ 0.025 (0.64) .001 sq pins typ 13 places 2x 1.050 (26.67) 0.100 (2.54) ref 0.050 (1.27) ref 1.000 (25.40) 2x 0.050 (1.27) 0.100 (2.54) typ 9 places pin assignments pin no. function 1 vout 2 vout 3 vout 4 trim 5 enable 6 power good 7 ground 8 ground 9 (+) sense 10 vin 11 vin 12 *mech support 13 *mech support *horizontal and smt version only
emerson network power and the emerson network power logo are trademarks and service marks of emerson electric co. ?2008 emerson electric co. emerson network power. the global leader in enabling business-critical continuity. emersonnetworkpower. com ac power connectivity dc power embedded computing embedded power monitoring outside plant power switching & controls precision cooling rev. 07.02.08 sil40c2 5 of 5 embedded power for business-critical continuity sxx06e rev. 08.01.06 page 1 of 2 americas 5810 van allen way carlsbad, ca 92008 usa telephone: +1 (760) 930 4600 facsimile: +1 (760) 930 0698 europe (uk) waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom telephone: +44 (0) 1384 842 211 facsimile: +44 (0) 1384 843 355 asia (hk) 14/f, lu plaza 2 wing yip street kwun tong, kowloon hong kong telephone: +852 2176 3333 facsimile: +852 2176 3888 for global contact, visit: www.powerconversion.com techsupport.embeddedpower @emerson.com while every precaution has been taken to ensure accuracy and completeness in this literature, emerson network power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. dimensions in inches (mm). tolerances (unless otherwise specifed) 2 places 0.030 (0.76) 3 places 0.010 (0.25) racks & integrated cabinets services surge protection surface mount pin assignments pin no. function 1 vout 2 vout 3 vout 4 trim 5 enable 6 power good 7 ground 8 ground 9 (+) sense 10 vin 11 vin 12 *mech support 13 *mech support *horizontal and smt version only dime nsions in inches (mm) tole rances (unless othe rw ise specified) 2 places 0.030 (0.76) 3 places 0.010 (0.25) 1.100 (27.94) 1.200 (30.48) pin 1 0.255 (6.48) 0.110 (2.79) ref 0.442 (11.23) 0.062 (1.57) ref 0.125 (3.18) typ 2x 1.050 (26.67) 0.100 (2.54) ref 0.050 (1.27) ref 1.000 (25.40) 2x 0.050 (1.27) 0.100 (2.54) typ 9 places
|
